996 Results
View results:
Sort by:
I still get an error message, although the WebService settings are activated in RFEM 6.
I still get an error message, although the WebService settings are activated in RFEM 6.
Data Exchange Between SCIA and DLUBAL
I get an error when importing an .xml file from SCIA to RFEM 6. How can I import SCIA files into RFEM 6?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Result Selection for Design Situation / Result Combination
Why are the maximum deformations not displayed?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Interface RFEM 6 / RSTAB 9 – IDEA StatiCa
How can I exchange data between RFEM 6 / RSTAB 9 and IDEA StatiCa?
Advantages of CFD Simulation
What are the advantages of CFD simulation compared to conventional experimental tests?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Saving Toolbars
I have customized my toolbars. How can I save these settings to use them on another computer?
Error Message when Accessing Template in Revit or Rhino/Grasshopper
I use a template for the data exchange with Revit or Rhino/Grasshopper, and get an error message.
How can I define temporary supports for a form-finding process in RFEM& 6?
How can I define temporary supports for a form-finding process in RFEM& 6?
Unit Stresses
Can I estimate which minimum cross-sections I should use before starting to design my model?
Member Nonlinearity
Is it possible to define member nonlinearities for beam members?
For example, can I define a member that absorbs all internal forces, except for the compressive axial forces?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM